Showing 641–660 of 985 results
Mobile Power Boost DIY 18650 Lithium Battery Digital Dual USB
Rated 0 out of 5
0 Reviews- USB Output: 5V 2.1A / 5V 1A(Dual USB interface).
- Batteries Type: liquid lithium-ion batteries (18650) 3.7 lithium-ion batteries only.
- Screen size: 27mm x 17mm.
- Charging voltage input: 5V-6V 1A.
- Step-up voltage output: 5V 1A/2.1A (Dual output, Total 2.5A).
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
Rated 0 out of 5
0 Reviews- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- Thermal Shutdown
- Under voltage and Over voltage shutdown
Motor Drive Board L293D Module For Arduino UNO MEGA 2560
Rated 0 out of 5
0 Reviews- New L293D motor shield, the input voltage DC4.5-25V
- 600mA output current capability per channel
MP1584 DC-DC 3A Adjustable Buck Module
Rated 0 out of 5
0 Reviews
Input Voltage: 4.5V – 28V ,Output Voltage: 0.8V – 20V, Output Voltage Adjustment: On-board potentiometer, Output Current: 1.8A (typical), 3.0A (max)., Ceramic Capacitor Stable, Internal Soft-Start, Internally Set Current Limit without a Current Sensing Resistor
MPU-6050 Triple-axis Accelerometer & Gyroscope
Rated 5.00 out of 5
(5.00)2 Reviews
It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel. Therefor it captures the x, y, and z channel at the same time. The sensor uses the I2C-bus to interface with the Arduino.
MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module
Rated 0 out of 5
0 Reviews
This is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ4 Methane gas sensor as a gas sensing element. It requires no external components just plug in Vcc & ground pins and you are ready to go
MQ-5 Methane LPG Liquid Propane Gas Sensor Module
Rated 0 out of 5
0 Reviews- Operating Voltage: 5V DC
- High sensitivity to LPG, natural gas, town gas.
- Small sensitivity to alcohol, smoke.
- Stable and long life.
- Simple drive circuit.
- Fast response.
MQ-7 Carbon Monoxide Coal Gas Sensor Module
Rated 0 out of 5
0 Reviews
Sensitive material of MQ-7 gas sensor is SnO2, which with lower conductivity in clean air. It make detection by method of cycle high and low temperature, and detect CO when low temperature (heated by 1.5V).
MQ-8 Hydrogen Gas H2 Sensor Module
Rated 0 out of 5
0 Reviews- Using high-quality dual-panel design, with power indicator and TTL signal output instructions.
- The switching signal having a DO (TTL) output and analog output AO.
- TTL output valid signal is low. ( Low-level signal when the output light can directly connect to the microcontroller or relay module )
- The higher the voltage, the concentration of the analog output voltage is higher.
- A hydrogen gas detection with good sensitivity.
- Rapid response and recovery characteristics
MQ-9 Carbon Monoxide, Methane and LPG Gas Sensor Module
Rated 0 out of 5
0 Reviews- Good sensitivity to CO/Combustible Gas
- High sensitivity to Methane, Propane, and CO
- Input voltage: DC 5±0.2V
- Current Consumption: 150mA
MT3608 2A DC-DC Step-Up Booster Power Module
Rated 0 out of 5
0 Reviews- It’s efficient up to 93%
- It can source a good amount of current
- The maximum output current: 2A
- Input voltage: 2V-24V DC
- The maximum output voltage: 5V-28V DC
Multi-Function Delay Timer Module Switch Control Relay Cycle Timer
Rated 0 out of 5
0 Reviews- Operating voltage: 6 - 30V DC
- 1 Channel delay trigerred relay module
- Delay time: 0.1 second ~ 999 minutes
- Seven Segment Display
