Motor Drivers circuits are current amplifiers. They act as a bridge between the controller and the motor in a motor drive. Motor drivers are made from discrete components which are integrated inside an IC. The input to the motor driver IC or motor driver circuit is a low current signal.
Showing all 18 results
BTS7960 43A H-Bridge High-Power Driver Module
Rated 0 out of 5
0 Reviews
BTS7960 High Power driver module comes with output Voltage indication of motor driver output end with heat sink solder. Output current is infinitely adjustable to meet various applications. BTS7960 Power driver large current (43 A) H bridge driver and 5V isolate with MCU, and effectively protect MCU.
DRV8833 2-Channel DC Motor Driver Module
Rated 0 out of 5
0 Reviews- Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor
- Operating voltage: 2.7 V to 10.8 V
- Output current: 1.2 A continuous (2 A peak) per motor
- Inputs are 3V- and 5V-compatible
Dual Monster Moto Shield VNH2SP30 DC Motor Driver 2x14A (Peak 30A)
Rated 0 out of 5
0 Reviews
Voltage Max: 16V, Maximum current rating: 30 A, Practical Continuous Current: 14 A, Current sensing available to Arduino analog pin, MOSFET on-resistance: 19 mΩ (per leg),Maximum PWM frequency: 20 kHz, Thermal Shutdown, Under voltage and Over voltage shutdown.
L9110S 2CH H-bridge Stepper Motor Dual DC Motor Controller Board
Rated 0 out of 5
0 Reviews
The L9110S Dual Channel Motor Driver Module is a compact board that can be used to drive very small robots.
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
Rated 0 out of 5
0 Reviews- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- Thermal Shutdown
- Under voltage and Over voltage shutdown
Motor Drive Board L293D Module For Arduino UNO MEGA 2560
Rated 0 out of 5
0 Reviews- New L293D motor shield, the input voltage DC4.5-25V
- 600mA output current capability per channel
Servo Driver-I2C-PCA9685 for Arduino-Raspberry Pi-16CH.-12Bit
Rated 0 out of 5
0 Reviews
This 16-CH. 12-bit PWM/Servo Driver-I2C-PCA9685 for Arduino-Raspberry Pi uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.Terminal block for power input (or you can use the 0.1" breakouts on the side).Reverse polarity protection on the terminal block input.3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
Stepper Motor Driver TB6600 Subdivision 4.0A 42V
Rated 0 out of 5
0 Reviews
TB6600 stepper motor driver provides maximum 4.0A output current. TB6600 comes with output sort-circuit protection, Low-Pressure shut-off, Overheating parking and over-current protection.
TB6560 Driver Board 3A CNC Router Single Axis Controller Stepper Motor
Rated 0 out of 5
0 Reviews
CNC Router Single Axis 3A Stepper Motor driver TB6560 board is for axis control with Input signal high-speed opto-coupler isolation, large heat sink to ensure good heat dissipation. Stepper motor driver is Semi-flow mode adjustable, semi-flow current adjustable,with a variety of semi-flow model and semi-flow current setting functions
TB6600 4.5A CNC Single-Axis Stepper Motor Driver Board Controller
Rated 0 out of 5
0 Reviews
Toshiba's new high current, high voltage TB6600HG new original chip, there are low-pressure shut-off, overheating parking and over-current protection circuit, short-circuit protection and increased compared to TB6560.
